System-sensor SP200 Series Dual Voltage Transformer Speakers User Manual download pdf

D400-69-00 1 I56-1217-008R

INPUT FROM

AMPLIFIER

TO NEXT

SPEAKER OR EOL

A0175-00

2. See Figure 2 as an example of how to select a

/4 Watt input

when a 25 volt amplifier is being used. Notice that the header,

SW1, has two shunts. One shunt is used to select either 25 or

70.7 volts input. The other shunt is used to select input power

/4,

/2, 1 or 2 Watts.

Figure 2:

25.0V

70.7V

1/2W

1/4W

25.0V

70.7V

1/2W

1/4W

CORRECT

SW1

INCORRECT

A0102-00

Specifications

Mechanical

Input Terminals: 12 to 18 AWG (3.31 to 0.82 mm

)

Speaker Size: 4 inches (101 mm)

Grille Size

Round: 6

/8″ (187 mm)

Square: 4

/8″ (127 mm)

Electrical

Voltage Input: 25 volts or 70.7 volts (nominal)

Maximum Supervisory Voltage: 50 VDC

Frequency Range: 400 – 4000 Hz

Operating Temperature Range: 32° to 120°F (0° to 49°C)

Power:

/4,

/2, 1 and 2 Watts

Listings: UL S4048

Storage Temperature: –20°C to 70°C

Operational Humidity Range: 10

– 93% RH (non-condensing)

NOTE: The SP200 Series is suitable for dry and humid environments. Not suitable for use in air handling spaces.

General Description

The National Fire Protection Association (NFPA) has published

standards and recommended practices for the speakers described

in this manual. As a result, the installer must be familiar with

these requirements as well as all local codes and special require

ments of the authority having jurisdiction.

SP200 series speakers can be operated with distribution amplifiers

having an output voltage of either 25 volts or 70.7 volts.

The speakers operate at any one of four input power levels. The

output sound level is selected at the time of installation, but can

be changed, if necessary.

The speaker is also equipped with a capacitive input to allow for

DC supervision.

Installation

All wiring must be installed in compliance with the National

Electrical Code (NEC) and applicable local codes as well as

special requirements of the authority having jurisdiction, using

the proper wire size. This also includes all applicable NFPA

Standards, ANSI/UL 1480, and NEC 760.

Electrical

1. Connect the speaker as shown in Figure 1.

NOTE: Do not loop electrical wiring under terminal screws.

Wires connecting the device to the control panel must

be broken at the device terminal connection in order to

maintain electrical supervision.

3825 Ohio Avenue, St. Charles, Illinois 60174

800/736-7672, FAX: 630/377-6495

www.systemsensor.com

INSTALLATION AND MAINTENANCE INSTRUCTIONS

SpectrAlert SP200 Series

Dual Voltage Transformer Speakers

for Fire Protective Signaling Systems

For use with the following models: SP200W, SP201R, SP201W

U.S. patent number: D424465

NOTICE: This manual shall be left with the owner/user of this equipment.

Figure 1.

Electrical

connections:

1 2

Summary of Contents

Page 1 - SpectrAlert SP200 Series

D400-69-00 1 I56-1217-008RINPUT FROMAMPLIFIERTO NEXTSPEAKER OR EOLA0175-002. See Figure 2 as an example of how to select a 1/4 Watt input when a 25

Page 2 - 2004 System Sensor

Figure 3:MountingSee Figure 3. The speaker can be flush mounted on a 4″ × 4″ × 21/8″ back box, as follows:A. Use the two 8-32 × 13/4″ screws, provided

Comments to this Manuals

No comments

System-sensor SP200 Series Dual Voltage Transformer Speakers User Manual

Browse online or download User Manual for Equipment System-sensor SP200 Series Dual Voltage Transformer Speakers. System Sensor SP200 Series Dual Voltage Transformer Speakers User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Equipment System-sensor SP200 Series Dual Voltage Transformer Speakers